Skip to content
M2M.globalGet early access

SIMCom SIM7070G: APN and network setup with an IoT SIM

Updated

The SIMCom SIM7070G is a cellular module for LTE-M and NB-IoT with 2G fallback. With an IoT SIM, you set the APN with AT+CGDCONT=1,"IP","<apn>", choose the radio technology, then check that the module is registered, at home or in roaming. Vendor commands come from SIMCom's manuals, standard ones from 3GPP TS 27.007; each cites its document.

Key facts

SIMCom describes it asLPWA module which supports wireless communication modes of Cat-M/Cat-NB/GPRS/EDGE
Radio technologiesLTE-M, NB-IoT, 2G
2G fallbackyes
GNSSnot stated
Form factorLCC, 68 pins, 24 × 24 × 2.3 mm
Variants and regionsGlobal bands for LTE-M and NB-IoT, plus GPRS/EDGE
Power savingPSM: yes; eDRX: yes

Source: SIMCom, SIM7070G product page. Checked 27 October 2026. SIMCom's manuals require a login on simcom.com: we read SIMCom's own documents in the versions named, which may be older than the current ones, and cite them by title and page.

Set the APN

AT+CGDCONT=1,"IP","<apn>"

Source: SIMCom SIM7070/SIM7080/SIM7090 Series AT Command Manual V1.05, pages 184 and 185.

Replace <apn> with the APN shown in your M2M.global account: the internet APN, or your private APN.

Choose the radio technology

AT+CNMP=38
AT+CMNB=1

AT+CNMP: 2 = automatic, 13 = GSM only, 38 = LTE only, 51 = GSM and LTE. AT+CMNB: 1 = LTE-M, 2 = NB-IoT, 3 = both.

Source: SIMCom SIM7070/SIM7080/SIM7090 Series AT Command Manual V1.05, pages 124 to 126.

Open the data connection

AT+CNCFG=0,1,"<apn>"
AT+CNACT=0,1

AT+CNCFG sets the APN of context 0 (1 = IPv4) for the internal applications; AT+CNACT=0,1 activates it.

Source: SIMCom SIM7070/SIM7080/SIM7090 Series AT Command Manual V1.05, pages 196 to 198.

Check that it works

AT+CPIN?        SIM ready? expect +CPIN: READY
AT+CEREG?       LTE registration: stat 1 = home network, 5 = roaming
AT+COPS?        network the module is using
AT+CGDCONT?     APN actually configured
AT+CSQ

An IoT SIM that works in many countries is often registered in roaming: +CEREG: 0,5 is a valid, working registration. Firmware that waits only for status 1 (home network) never goes online on such a SIM. Status values come from 3GPP TS 27.007; the signal command from SIMCom SIM7070/SIM7080/SIM7090 Series AT Command Manual V1.05, pages 66 and 67.

To save battery, request PSM with AT+CPSMS and eDRX with AT+CEDRXS (3GPP TS 27.007); the network decides which timers it grants.

Networks and shutdowns

The SIM: IoT SIM cards and IoT eSIM. All commands explained: AT commands.

Frequently asked questions

How do I set the APN on the SIMCom SIM7070G?

Send AT+CGDCONT=1,"IP","<apn>", with the APN of your SIM in place of <apn>. Source: SIMCom SIM7070/SIM7080/SIM7090 Series AT Command Manual V1.05.

Does the SIMCom SIM7070G support LTE-M and NB-IoT?

SIMCom states both for the SIM7070G: LTE-M and NB-IoT with 2G fallback.

Does the SIMCom SIM7070G fall back to 2G?

Yes, SIMCom lists 2G (GSM/GPRS/EGPRS) fallback for the SIM7070G. It only helps where operators still run 2G.

Why does my SIM7070G show +CEREG: 0,5?

Status 5 means registered in roaming, a normal working state for an IoT SIM that uses partner networks. Treat it like status 1 (home network) in your firmware.